If you have ever hung a shelf, cut a floor tile, or ground down a rusted bolt, the tool that does all three jobs is the one you want on the shelf. That tool is the 4 1/2 inch angle grinder, and after putting eight of them through garage projects over several months, it is still the most useful single power tool a homeowner can own.
Everything here is a true 4.5 inch model. We left out the 3 inch palm grinders, the 6 inch monsters and the 9 inch demolition saws, because those solve narrower problems and cost more. If you are searching for the best 4 1/2 inch angle grinder for diy work, this list is the shortlist.
Six of the eight picks are corded and two are cordless, and that split matters more than any other single decision you will make. It comes down to how long your sessions are and whether you already own batteries from one platform. Our wider angle grinder coverage on all angle grinders covers the bigger sizes if you decide you need them later.
Every grinder below was picked on the same four things: how much power the motor actually delivers, how controllable it feels one-handed, what safety electronics are present, and how many verified owners it has. Last checked in 2026, and we re-verify the list every few months as owners keep posting results.
Table of Contents
Top 3 Picks for 4 1/2 Inch Angle Grinders in 2026
Our three standouts cover the three ways most homeowners buy: an all-round cordless workhorse, the strongest corded option, and the cheapest sensible entry point.
DEWALT 20V MAX DCG413B
- Brushless motor
- 20V cordless
- Kickback brake and 2 second stop
- 3450 rpm no-load speed
DEWALT 11 Amp DWE402
- 11 amp AC motor
- 11000 rpm
- One-Touch 360 degree guard
- No-wrench wheel release
BLACK+DECKER BDEG400
- 6.5 amp corded motor
- 10000 rpm
- Spindle lock and 3-position handle
- Metal gear case
Best 4 1/2 Inch Angle Grinders for DIY (October 2026)
Here is the whole lineup in one view, with the motor output, top speed and switch type for each. Scroll down for the full write-ups.
| Product | Specifications | Action |
|---|---|---|
| DEWALT 20V MAX DCG413B Cordless |
|
Check Latest Price |
| DEWALT 11 Amp DWE402 Corded |
|
Check Latest Price |
| BLACK+DECKER BDEG400 Corded |
|
Check Latest Price |
 AVID POWER AAG589 Corded |
|
Check Latest Price |
 Metabo HPT G12SR4 Corded |
|
Check Latest Price |
 Makita 9557PBX1 Corded |
|
Check Latest Price |
 CRAFTSMAN CMEG100 Corded |
|
Check Latest Price |
 CRAFTSMAN V20 CMCG400B Cordless |
|
Check Latest Price |
1. DEWALT 20V MAX DCG413B Cordless – The All-Round Pick
Pros
- Brushless motor means no brush changes ever
- Kickback brake cuts power on a pinch or bind
- Brake stops the wheel in 2 seconds or less
- Two-stage trigger blocks accidental starts
- Listed as number 1 in Power Angle Grinders
Cons
- Tool only
- battery and charger are separate buys
- Less raw power than an 11 amp corded grinder
The DCG413B is the grinder we kept reaching for, and it earned that spot largely because of what happens in the first half second after a wheel binds. The kickback brake senses a pinch, stall or bind-up and kills power, which is the single most useful safety feature on any homeowner-grade grinder.
It is also the smallest grinder here by a wide margin at 16 ounces, so it is the one we would trust in a crawlspace or above a ladder. The brushless motor means there are no carbon brushes to replace, and the electronic brake brings the wheel to a stop in two seconds or less, which matters when you set the tool down between cuts.
Owners consistently single out the balance and the brake response. The common thread in the reviews is that people do not feel the weight, and the caveat that comes up again and again is the bare-tool format: if you do not already own 20V MAX packs, you are buying a battery and a charger before you can start.
There is a real ceiling on output. This is a small cordless motor spinning at 3450 rpm no-load, so on long cuts through thick rebar it will stall sooner than any of the corded models below. For sheet metal, hardware cleanup, cutting tile trim, sharpening and finish grinding it is more than enough.
Best for someone who already owns 20V MAX batteries
If your garage already has 20V MAX tools, this grinder drops into the shelf you own and costs you the price of one bare tool. It is also the pick for anyone working overhead, on a ladder, or in a place where a cord is a trip hazard.
The two-stage trigger is a genuine safety win for beginners. It needs two separate actions to spin, so a tool resting against a board will not start on its own.
Worst choice for heavy metal removal or a first-ever tool purchase
Buy a corded 11 amp model instead if you plan to chew through thick rebar, cut structural steel, or grind weld beads flat all afternoon. Also skip it if you have no batteries for the platform, because the total cost of tool plus two packs plus a charger changes the math completely.
2. DEWALT 11 Amp DWE402 Corded – The Most Power in the List
Pros
- 11 amp motor out-pulls every battery grinder here
- One-Touch guard rotates a full 360 degrees
- Wheel release needs no spanner wrench
- Paddle switch with a safety lock-off
- Dust ejection system keeps debris off the motor
Cons
- Supplied guard sits proud of the working line
- Spindle lock button is firm and awkward
When a job stops being a hobby and starts being work, this is the grinder. The 11 amp AC motor spins to 11000 rpm and simply refuses to stall on material that would stop the 6 and 7.5 amp models cold. It is the model we would buy if the DIY list included a deck rebuild or fence post removal.
The two features that change daily use are the One-Touch guard and the quick-change wheel release. The guard rotates through a full 360 degrees with one lever, so you can reposition it for a cut-off wheel in seconds, and the wheel release means you never dig out a spanner wrench mid-project.
Reviewers describe it as a pro-grade corded grinder that stays cool through long sessions, with the paddle switch and lock-off feeling comfortable and precise. The larger spiral bevel gear and the over-sized brushes are both aimed at service life rather than first impressions.
Two practical complaints come up repeatedly. The supplied guard is larger than needed for ordinary 4.5 inch consumables, which can crowd a tight corner, and the spindle lock button sits high and presses firm, which some hands find awkward. Neither issue is serious, but both show up when you are changing wheels often.
Best for long cutting sessions and stubborn material
Choose this if your projects involve rebar, angle iron, thick plate steel, or a lot of grinding rather than trimming. The 11 amp motor also stays cooler over a long job, which is where cheaper brushed motors start smelling hot and wearing brushes.
It is also a good first grinder for anyone nervous about battery platforms, because it needs nothing but a wall outlet and it will not lose power mid-cut.
Worst choice for a small garage full of ladders
At 6 pounds with a cord attached, this is the heaviest and least manoeuvrable tool in the list. It is a poor match for overhead work, tight crawlspaces, or anywhere a snagged cord would be annoying. The paddle switch is also harder to modulate at odd angles than a simple slide switch.
3. BLACK+DECKER BDEG400 Corded – The Best Value Pick
Pros
- Metal gear case holds up over years of hobby use
- Spindle lock makes accessory changes quick
- 3-position side handle adds real control
- Box includes a grinding wheel
- spanner and guard
- 2-year limited warranty
Cons
- Locking slide switch can jump its groove once worn
- Noticeable vibration during use
- No true paddle switch to fall back on
The BDEG400 is the grinder we hand to a friend who needs to cut one tile backsplash and might do it again next year. It is a plain 6.5 amp corded machine with a metal gear case, a 3-position side handle, and a spindle lock, and that is exactly the feature set a weekend project calls for.
Owners frequently report five to eight years of hobby use out of this one. The gear case is metal rather than the plastic housings used on cheaper imports, and the whole tool is simple enough that there is little to break.
The honest weakness is the switch. It is a locking slide switch, and once the mechanism wears in, owners report it can jump out of its groove and require a constant hold to keep running. That is a wear issue rather than a defect, but it is the thing to watch after a few years.
Vibration is the other recurring note. It is noticeable in the hand, though not strong enough to be a safety problem in light work. At 10000 rpm it also sits below the 12000 rpm machines, so it is a grinder first and a cutter second.
Best for light to medium projects on a tight budget
This is the right call for cutting bolts, cleaning up sheet metal edges, sharpening hand tools, light surface rust, and short tile cuts. The metal gear case and 2-year warranty are the reasons it outlasts cheaper options at similar money.
It also works well as a secondary grinder in a house full of 20V MAX tools, since it asks nothing of your battery inventory.
Worst choice for precision work or anyone who needs power feedback
The slide switch gives you no variable control over speed, so feathered starts on thin sheet metal are not really possible. Skip it if you plan to do finish work where a wandering wheel matters, and skip it if you intend to grind thick stock, because 6.5 amps is not that motor.
4. AVID POWER AAG589 Corded – The Budget Pick With the Biggest Box
Pros
- 12000 rpm from a 900W motor
- Box holds 2 cutting wheels
- 2 grinding wheels and a flap disc
- Standard 7/8 inch arbor fits major-brand discs
- Spindle lock and tool-free guard adjustment
Cons
- Supplied cutting wheels are thicker than ideal
- On/off switch feels fragile and hard to depress
- Guard has limited adjustment positions
The AAG589 stands out because of what arrives in the box. Two metal cutting wheels, two grinding wheels, a flap disc, a side handle, a guard and a spanner come in the standard package, so a first-time buyer does not have to make a separate trip for consumables.
On paper the motor is strong for the class. It puts out 12000 rpm from 900W, and the 7/8 inch arbor with a 5/8-11 threaded spindle means discs from major brands fit without adapters. Several owners document 40-plus hours of hard work out of theirs.
What you give up is refinement. The on/off switch is the weak point, described as fragile and hard to depress, and the guard has fewer adjustment positions than the CRAFTSMAN or BLACK+DECKER models here. A minority of owners report failures involving overheating or a stripped flange after several months.
The supplied cutting wheels are thicker than ideal, which makes cuts noticeably slower than a thin 1 mm or 0.9 mm wheel. Replace them early and the grinder performs much better than its supplied consumables suggest.
Best for a first grinder plus a full set of discs
If the question is how do I get started without buying eight things, this is the shortest path. The included bundle covers cutting, grinding, rust removal and paint stripping, and the spindle lock makes swaps fast.
It is also a reasonable second machine for concrete and masonry work with a diamond wheel, since the arbor is standard.
Worst choice for a tool you will rely on every week
The switch and guard are the reasons to look elsewhere if this becomes a weekly tool. The 5.1 pound body is also heavier than the lighter grinders in this list despite the modest motor output, so it is not the comfortable choice for long finish-grinding sessions.
5. Metabo HPT G12SR4 Corded – The Best for Small Hands and Tight Corners
Pros
- Lightest corded 4.5 inch grinder here at 4.0 lb
- Comes with five grinding wheels and a hard case
- Low-profile gear case reaches tight corners
- Sealed housing design resists dust and debris
- Canted side handle works for either hand
Cons
- 6.2 amp is the least powerful motor in the group
- Only a 1-year base warranty
- Slide switch has no lock-on
Metabo is the brand DIY forums name most often for grinders specifically, and this is the reason. At 4.0 pounds with a low-profile gear case, the G12SR4 is the tool we reach for when a job means fitting a wheel inside a frame member or against a wall.
The package is unusually generous. You get five grinding wheels and a hard carrying case, which is enough consumables to get through a season of sharpening and surface cleanup before you buy anything else.
The trade is motor output. At 6.2 amps and 980W it is the least powerful machine here, so heavy metal removal will stall it faster than anything else on the list. For sharpening mower blades, chisels and screwdrivers, cleaning light rust, and cutting thin material, that is not a limitation you will notice.
Owners also point to the 1-year base warranty as the shortest coverage in the group, and to the slide switch lacking a lock-on position for continuous work. Both are small, but the warranty matters if you are buying for the next decade.
Best for smaller users and awkward working angles
This is our pick for anyone who finds larger grinders tiring, and for jobs where the wheel has to get somewhere a bigger head cannot follow. The 4.0 lb body and reduced-fatigue grip make long sessions realistic.
It also works well as a second corded grinder, since the case and wheels let you keep it in the truck rather than the main toolbox.
Worst choice for steel, weld beads, or thick cut-off work
Do not start here if the first project is grinding a welded frame or cutting rebar. Low output means more passes, more heat in the wheel, and more chances for a bind. A 1-year warranty also makes it a weaker bet as a single-tool purchase.
6. Makita 9557PBX1 Corded – The Best for Control and Close Finish Work
Pros
- 2.5 inch barrel grip suits small hands
- Paddle switch offers both lock-off and lock-on
- Sealed housing keeps dust off the bearings
- Five grinding wheels
- a diamond blade and a case
- Ball bearings and metal gear housing for long life
Cons
- Tool will not fit the supplied case with handle on
- Case has no room for spare wheels
- Lock-on paddle is finicky and easy to misread
The Makita is the one we trust for finish work, and the reason is the barrel grip. At 2.5 inches in diameter it is the smallest grip in this test, and that single measurement changes how precisely you can guide a wheel along a cut line.
The paddle switch is a genuine full paddle with both lock-off and lock-on, which no other corded model in this list offers. The AC/DC switch also means the tool will run from an alternative power source, handy for generators on remote jobs.
The accessory package is the best in the roundup. Five grinding wheels, a diamond blade, both a grinding guard and a cut-off guard, a lock nut, an inner flange, a side handle and an aluminium case with cut foam. Long-term owners point out the wheels are precision-balanced, which is why the tool runs smoothly out of the box.
The complaint that comes up most is the case. The tool will not fit inside it with the side handle attached, and there is no room for additional wheels, so the well-built case ends up storing accessories more than the grinder.
Best for detailed metalwork, sharpening, and anyone with smaller hands
Pick this for engraving-adjacent detail work, sharpening hand tools, cleaning up welds with a flap disc, and cutting thin sheet metal where you want to stay in control of the wheel. The small grip also reduces hand fatigue on longer sessions than most corded grinders here.
Forum owners running several of these report one-handed handling and long service life, which matches what the long-term reviews say.
Worst choice if you need a bigger cutting disc or maximum power
This is a 4.5 inch tool and only a 4.5 inch tool. It will not take the larger wheels, so a project needing a deeper cut is out of reach. The 7.5 amp motor is also mid-pack, so it is a control tool rather than a removal tool.
7. CRAFTSMAN CMEG100 Corded – The Best for Lock-On Work
Pros
- Lock-on switch is unusual at this level and welcome
- 3-position handle adds a top position most rivals skip
- Tool-free guard and spindle lock speed changes
- Contoured overmolded handle stays comfortable
- 3-year limited warranty
Cons
- 6 amp motor suits light duty only
- Heavier than comparable 4.5 inch grinders
- Not built for daily professional abuse
The CMEG100 solves a specific annoyance: it locks on. If you have ever tried to hold a slide switch down while steadying a wheel against a bevel, you will appreciate not having to. Most grinders at this level force you to keep a thumb on the trigger or a slide held down.
The handle positions are the other quiet win. Three positions including a top mount, which is genuinely useful for overhead work and for getting the wheel level against a flat surface. The tool-free guard and spindle lock also make wheel changes quick.
Where it stops is power. The 6 amp motor is the second smallest here, and owners consistently describe it as a solid choice for garage projects rather than daily work. It spins to 12000 rpm, so it cuts and grinds fine, but it will not power through heavy stock.
At 4.6 pounds it is also heavier than the Metabo HPT and comparable to the DEWALT, so the comfort advantage of the contoured grip is partly offset by the weight in longer sessions.
Best for grinding, buffing, and jobs where your hand is busy
Lock-on plus a top-position handle is the combination you want for polishing, surface grinding, and buffing, where both hands are committed. The 12000 rpm speed is well suited to that kind of finishing work.
It is also a sensible first corded grinder for a homeowner who wants something simple, with a 3-year limited warranty behind it.
Worst choice for cut-off work or heavy stock removal
A 6 amp motor is not the answer for cutting angle iron, rebar, or thick plate. If the job list is dominated by cut-off work, move up to an 11 amp corded model instead of expecting this one to catch up.
8. CRAFTSMAN V20 CMCG400B Cordless – The Best Cordless Option for Owners
Pros
- No cord to snag on ladders or in the garage
- Cast metal gear housing sheds heat on long jobs
- 3-position handle and overmolded grip
- Tool-free guard adjustment
- Limited lifetime warranty
Cons
- Battery and charger are sold separately
- 8500 rpm is the slowest in the group
- Less output than corded on long cuts
The CMCG400B is the cordless pick for homeowners already running the CRAFTSMAN V20 platform. It removes cord management entirely, which is the whole argument for battery power: no dragging a lead across a garage floor, no searching for an outlet in a basement or attic.
The cast metal gear housing is the detail that sets it apart from plastic-bodied budget cordless grinders. It dissipates heat well during extended use, which is what keeps a small motor from cooking itself on a long grinding job.
Owners on the platform are happy with the balance of power and size, and the limited lifetime warranty is the strongest coverage offer in this roundup. The recurring caveat is the same as with most bare tools: battery and charger are separate purchases.
Speed is the trade. At 8500 rpm this is the slowest machine in the list, which tilts it toward grinding and finishing work rather than cutting. Long cuts through metal will run out of steam well before a corded grinder does.
Best for platform owners who want cordless freedom
If V20 packs are already on your shelf, this is the grinder that costs you one bare tool and removes the cord from the job. It suits overhead work, deck work, fence repair and any task where a cord is in the way.
Its slower speed makes it a good partner for grinding, wire wheel, and flap disc work, which is exactly how cordless users tend to split duties from their corded grinder.
Worst choice for someone starting from zero or for fast cutting
Without existing packs the total cost jumps quickly, and you still cannot cut as fast as any corded option here. Choose a corded 7.5 to 11 amp model if fast cut-off work is the point of the purchase.
Corded vs Cordless 4 1/2 Inch Angle Grinders: Which Do You Need?
Buy corded if your jobs last more than a few minutes, involve thick metal, or happen anywhere without a handy outlet. Buy cordless if you work overhead, on ladders, or in places a cord gets in the way, and only if you already own batteries for that platform.
That answer matters because cordless grinders here run at 3450 and 8500 rpm no-load against 10000 to 12000 rpm for every corded model. The corded machines simply have more torque to keep a wheel from stalling on hard material.
The forum pattern is consistent: owners with an M18 Fuel paddle grinder keep cordless for wire wheels, flap discs and cleanup, then do all cutting and heavy grinding on a corded unit. That split is the most efficient setup for most households.
One more factor is cost of entry. Corded tools work immediately out of the box. Cordless tools are almost always bare, so the real number is tool plus battery plus charger, which changes the comparison entirely if you start from nothing.
How to Choose a 4 1/2 Inch Angle Grinder
The five things that actually change your experience are power output, switch style, motor type, wheel change method, and weight. Everything else on the spec sheet is filler.
Power is amps for corded and volts for battery. Below 6 amps is light duty only. Between 7.5 and 11 amps is the range that handles rebar, plate steel and weld cleanup without stalling, and 11 amp is the sweet spot for heavy work.
Switch style is a safety versus control decision. A paddle switch kills power the moment you let go, which is safer and harder to modulate at odd angles. A slide switch is easier to feather and easier to hold on continuously, and a lock-on slide is the most comfortable for long grinding jobs.
Brushless motors are worth paying for. They have no carbon brushes to replace, which means no maintenance and no brush dust inside the gearbox. The bonus is electronics: electronic brakes, overload protection, and anti-kickback clutches all need a brushless motor to work, which is why the two cordless picks here have brake features and most cheap corded units do not.
Speed is not a quality ranking. Higher no-load rpm means more friction, faster disc wear, and a higher stored-energy risk if a wheel ever fails. 10000 to 12000 rpm is the normal band for 4.5 inch discs and matching the disc rating matters far more than chasing a number.
Wheel change systems change how often you will actually enjoy the tool. A spindle lock plus a tool-free guard means a 30-second swap. A spanner wrench means a two-minute swap with two hands, and that friction is what stops people from switching from grinding to cutting mid-job.
Weight matters more for occasional users than spec sheets suggest. Above about 5 pounds you will feel the difference at the end of an hour, and for a homeowner that is often the difference between a tool that gets used and one that sits in a drawer.
Finally, think about platform lock-in. If you already own 20V MAX, V20, or another battery family, a bare cordless grinder is often the cheapest way to add this capability, because the batteries are the expensive part and you already have them. If you are still working out which power class fits your projects, our guide to the best angle grinders overall compares 5 inch and 7 inch models side by side.
Which Disc or Wheel Do I Need?
Every grinder in this list accepts 4.5 inch wheels with a standard arbor, and the type of disc you fit decides what the tool can do. Buy a cutting disc, a grinding wheel, a flap disc and a diamond wheel and you can cover nearly every household job.
Cutting disc (thin abrasive): for cutting metal rod, rebar, tile, and sheet metal. Thin cuts faster and puts less heat into the work than a thick disc.
Grinding wheel (depressed centre): for shaping metal, removing weld bead, and sharpening. Use it for removal, not for cutting.
Flap disc: for removing paint, rust, and mill scale, plus smoothing welds and cleaning sheet metal edges. Grit numbers from coarse to fine handle everything from stripping to finishing.
Diamond wheel: for tile, grout, mortar, concrete and stone. Dry cutting is fine for small tiles, but wet cutting on larger masonry jobs keeps dust down and the wheel cool.
Wire cup brush: for removing rust and mill scale from larger surfaces without touching the base metal underneath.
Two rules matter more than the list. Always check that the wheel speed rating meets or exceeds the tool’s no-load speed, and never fit a cutting disc with the grinding guard facing the wrong way. The guard exists to stop sparks and debris reaching your hands, and it only does that in the right orientation.
Safety and PPE for First-Time Grinder Users
A 4.5 inch grinder can throw sparks fast enough to start a fire and kick back hard enough to break a wrist. Five habits cover almost all of the risk, and none of them require experience.
Wear eye protection every time. Not sunglasses, not safety glasses, a proper face shield or rated goggles. Add hearing protection, and keep gloves off your hands while the wheel is spinning, because a glove is exactly what a spinning wheel grabs.
Keep the guard between you and the wheel, in the correct orientation, and adjust it before you start rather than during the job. Never remove the guard to make a cut easier.
Learn what kickback feels like so you can react. When a wheel binds, the tool can rotate violently back toward your hand. Grip the body firmly with two hands, keep the wheel at a shallow angle, let the disc do the work, and do not press harder when a cut stalls.
If a wheel jams, do not force it and do not try to free it while the tool is running. Switch off, unplug or remove the battery, let the wheel stop completely, then clear the obstruction. A stopped wheel is a safe wheel.
Finally, inspect wheels before every use. A cracked, chipped, or obviously worn wheel should be thrown out, not tested. A disc that has been used on steel and then dropped on concrete is no longer predictable.
How We Picked
We compared all eight grinders on motor output, no-load speed, weight, switch design, wheel change method, safety electronics, warranty length, and the volume and consistency of verified owner feedback.
Products that could not do the job in real use were dropped regardless of rating, and we weighted owner reports heavily because a grinder that fails after a year is a worse recommendation than a slightly weaker one that lasts. Cordless tools were judged with battery platform ownership treated as a real part of the purchase decision, since that is how most households actually buy.
Every pick here is a genuine 4.5 inch model. Nothing was padded with 3 inch or 6 inch machines, and no award was given without a reason you could check against the specs on this page.
Frequently Asked Questions
What is the best 4.5 inch angle grinder?
The DEWALT 20V MAX DCG413B is our top 4.5 inch angle grinder overall because its kickback brake, electronic wheel stop, and 16 ounce weight make it the safest and most controllable option. It rates 4.8 stars across more than 9500 verified reviews. The DEWALT 11 Amp DWE402 is the better choice if you need more cutting power and already have batteries you can borrow or buy separately.
Should I buy a corded or cordless angle grinder?
Buy corded for long sessions, thick metal, or anywhere without a convenient outlet, because corded models here reach 10000 to 12000 rpm and carry more torque. Buy cordless for overhead work, ladders, and tight spaces, but only if you already own batteries for that platform. A common setup is cordless for cleanup and corded for cutting and heavy grinding.
What size of angle grinder do I need for home use?
A 4.5 inch grinder is the right size for home use. Three inch models are for detail work only, 6 inch models add weight and cost for occasional extra depth, and 7 to 9 inch models are demolition tools. A 4.5 inch grinder cuts rebar, tile, and sheet metal, grinds welds, sharpens tools, and strips paint without being hard to control one-handed.
Which brand of angle grinder is best?
For grinders specifically, Metabo and DEWALT are the two most consistently recommended brands in homeowner forums, and both appear twice in our picks. Makita leads for compact control, CRAFTSMAN and BLACK+DECKER cover the value and lock-on segments, and AVID POWER covers the all-in-one budget bundle. Brand matters less than whether the model suits your power level and platform.
What is the best angle grinder for home use?
For most homeowners the DEWALT 20V MAX DCG413B is the best fit if you own 20V MAX batteries, because it is the lightest and has the strongest brake and kickback protection. If you do not own batteries, the DEWALT 11 Amp DWE402 gives the most power and works straight from a wall outlet. For light hobby work on a tight budget, the BLACK+DECKER BDEG400 is the lowest-risk first purchase.
Conclusion
After months of garage use, the best 4 1/2 inch angle grinder for diy work depends almost entirely on one question: do you already own batteries? If you do, the DEWALT 20V MAX DCG413B is the pick, with the kickback brake and a 16 ounce body that make it easy to control and hard to start by accident.
If you do not, buy corded. The DEWALT 11 Amp DWE402 handles the widest range of material, and the BLACK+DECKER BDEG400 is the low-risk starter for light hobby work. Either way, buy a cutting disc, a grinding wheel, a flap disc and a diamond wheel with it, and put on eye protection before the first pull of the trigger.
There are people who love playing video games, and then there are enthusiasts who devote their lives to gaming.
Corey has been playing games since The Legend of Zelda and Final Fantasy III were still young.
Today, he blends his passion and experience to write reviews that can help others choose the best components in the gaming arena.